![]() Verify that the dial has completely stopped (turning to the right) on or about "87" before turning the handle. When the handle is forced it will slip left or right.Ĭombination Works but Handle Will Not Turn The handle has a built in clutch mechanism. Why is the handle pointing in a different direction than it used to be? The warranty does not cover lost or forgotten combinations, failed combination changes, improper opening procedure, and weak or dead batteries. To verify if your safe can have an Mechanical lock installed Click Hereĭoes my warranty cover me if I lost the combination to my safe? Most Electronic locks can be swapped out with an Mechanical lock. Tightness of dial may increase or decrease as dial is being turned.Ĭan I replace the digital keypad with a mechanical lock? Normally dial tightness varies from safe to safe. Make sure the door is completely closed and the locking bolts are in the fully extended position. Excessive bolt pressure may be due to improper personal storage. Some free play should exist in the handle, left to right. Verify that the key-lock is unlocked before attempting to turn dial. ![]() Try dialing 1 up or 1 down from each number in the combination.Ĭombination Dial is Tight or Will Not Turn The combination number may have shifted slightly during shipping. PLEASE NOTE: If your lock still does not open, it is possible that one or more of your numbers may be off slightly from those shown in this manual. Then turn the dial right until it stops at about "87". Hold dial on "0" while rattling the handle left and right. ![]() Redial the complete combination stopping at "0" (before reaching "87"). Each turn of the dial engages another part of the mechanism, creating more resistance to dialing.Ĭheck lock-bolt pressure. During the dialing process, it is normal to feel more resistance each time the dial is turned a complete revolution. Some resistance should be felt as the mark representing “97” comes under the opening index, and the dial should reach a positive stop near “87.” The lock is now open, turn the opening handle to release the door. Turn the dial to the left (counterclockwise) stopping the second time the third number of the combination aligns with the opening index.Ĥ. Turn the dial to the right (clockwise), stopping the third time the second number of the combination aligns with the opening index.ģ. Turn the dial left (counterclockwise), stopping the fourth time the first number of the combination aligns with the opening index.Ģ. The procedure for a Sargent & Greenleaf three-wheel lock is as follows:ġ. If you dial past the intended number even slightly, begin the entire dialing procedure again. This helps ensure the number you are entering will be aligned directly under the index mark. While performing any procedure involving dialing numbers into the lock, it is important to view the dial and ring straight on. The mark at the eleven o’clock position (if present) is used only for changing the combination. The one at the twelve o’clock position is used in dialing open the lock. An important point to remember is that there are usually two index lines on a dial ring. There is a simple, definite procedure which must be followed to achieve consistent success. If you are having a hard time opening your mechanical lock watch this short video to make sure you are inputting digits correctly.Ī very high percentage of lockouts are due to the end user’s improper dialing of the combination lock. Mechanical dials are confusing, how do I open my safe? To verify if your safe can have an electronic lock installed Click Here Most mechanical locks can be swapped out with an electronic lock. Yes, your combination is stored within the locks computer and will not be affected if you change the battery or if the battery dies.Ĭan an electronic lock be installed on my safe? If the batteries die does the lock remember my combination? Push keypad back into plastic base and test. Remove the keypad from plastic base by pulling straight out, careful to not damage wire connecting keypad to base. Refrain from pushing buttons while the battery connects or the timer will reset. ![]() The combination is stored in the locking body and will remain the same. However, the battery compartment is located on the outside of the safe so you can still change the battery and regain access to your safe, even if it dies. Is there a backup way to get into the safe if my batteries die?įor added security there is no other way to get into the safe, making it very important to check battery life.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |